2026-09-23 8 min read

Pool Excavation Calculator

Free pool excavation calculator — calculate pool excavation excavation with overdig, spoil, loads and cost. Includes live results, step-by-step working, charts, material takeoff and cost estimates. No sign-up.

Calculator

Length(ft) Help

Design size

Width(ft) Help

Design size

Depth(ft) Help

Plus freeboard

Overdig/side(ft) Help

Working room

Swell(%)

Price (optional)($/bank yd) Help

$/bank yd

Dig rate

Dig plan

Item	Amount
Neat volumeDesign size	94.81 cu yd
Dig volumeWith overdig — dig this	160.00 cu yd
SpoilLoose — haul this	200.00 cu yd
Haul loadsAt 14 cu yd each	14.3

How to use this result

Primary result: 160.00 cu yd — verify it against a rough hand check before ordering.
Read the steps section to see every conversion and the exact formula path.
Use the breakdown table on the left as your order or bid checklist.
Re-run with worst-case dimensions so the plan covers the whole job.

Results

Normal

Dig volume

160.00cu yd

Bank yards with overdig

Neat volume

94.81cu yd

Design size only

Spoil (loose)

200.00cu yd

Haul this

Haul loads

14.3loads

At 14 cu yd each

Live results update as you type — currently showing 160.00 cu yd. Replace the defaults with your own measurements for exact results.

Visualizations

Neat vs dig (cu yd)

94.8Neat

160Dig

200Spoil

Neat vs overdig+swell

Neat47%

Extra53%

Formula

Rectangular dig is box volume with overdig each side and extra depth.

V = L × W × D ÷ 27

Variables

Symbol	Name	Unit	Description
L, W, D	Dimensions	ft	Design plus overdig.
bank	Bank	cu yd	To dig.
loose	Loose	cu yd	To haul.

Explanation

Neat design volume plus overdig at full precision; swell sizes spoil; trucks divide haul loads.

Step-by-Step Calculation

Follow each step to understand how the result is calculated from your inputs.

Step 1

Neat design volume.

32 × 16 × 5 ÷ 27

Result: 94.81 cu yd neat

Step 2

Dig with overdig each side plus 1 ft depth.

36.00 × 20.00 × 6.00 ÷ 27

Result: 160.00 bank · 200.00 loose

Final Answer

160.00

Worked Examples

See how the calculator works with different scenarios.

Scenario

The calculation run on the values above, showing the full path rather than only the answer.

Inputs

Result:160.00 cu yd

Calculation

1. Neat design volume. → 94.81 cu yd neat 2. Dig with overdig each side plus 1 ft depth. → 160.00 bank · 200.00 loose

Result

160.00 cu yd

Interpretation

Probe every pad and trench, separate topsoil from spoil, and book trucks to the loose volume — not the bank figure.

Understanding Your Result

Your Result: Dig volume: 160.00 cu yd

Typical range: Pickup ~2 cu yd · dump truck 10–16 loose cu yd · trench 1 ft × 100 ft × 4 ft ≈ 15 bank cu yd.

What This Means

Your result is 160.00 cu yd — the bank and loose volumes, truckloads and cost for your pool excavation

Why It Matters

Earthwork is the first money spent and the easiest to misjudge: swell multiplies spoil, haul distances multiply cost, and rock stops everything. Quantities first keeps the site moving.

Professional Interpretation

Probe every pad and trench, separate topsoil from spoil, and book trucks to the loose volume — not the bank figure.

How this is calculated

Dig = (design + overdig) dimensions ÷ 27. Soil factors apply last; trucks round up.

What drives the result

The inputs in a single consistent unit and the allowance or price you apply.

Recommendations

•Verify critical dimensions on site before ordering.
•Keep one unit throughout each calculation.
•Add the trade allowance before buying, not after.
•Attach the step-by-step working to bids and records.

Educational Content

Introduction

Earthwork quantity is geometry with soil factors: bank volume from dimensions, loose with swell, compacted with shrinkage, trucks from payload.

Concept Explanation

Dig = (design + overdig) dimensions ÷ 27. Soil factors apply last; trucks round up.

Applications

▸Pad, trench and basement takeoffs

▸Cut, fill and balance planning

▸Haul truck scheduling and spoil piles

▸Topsoil, base and bedding quantities

▸Grading and compaction estimates

Benefits

•Bank, loose and compacted figures together
•Swell and compaction factors built in
•Truckloads rounded up for scheduling
•Free, no sign-up, works on site from a phone

Limitations

•Two-dimensional math unless stated otherwise — slopes and curves need the right tool
•Results are only as good as the site measurements
•Allowances and prices are estimates — confirm with local quotes

Best Practices

•Measure twice and write measurements down before typing them in
•Keep one unit throughout each calculation
•Photograph the tape on large or disputed measurements
•Re-run with worst-case numbers so the plan covers the whole job

Common Misconceptions

Myth: The calculator replaces site verification.

Truth: It replaces the arithmetic, not the tape measure — always verify before ordering.

Myth: One decimal place is always enough.

Truth: On long runs, rounding early compounds. Enter full measurements and let the tool round at the end.

Myth: Metric and imperial give different answers.

Truth: They are the same physical quantity in different units — conversion is exact.

Practical Tips

•Enter full measurements and let the tool round at the end.
•Use the steps section to double-check the formula path.
•Save or share the result link with the crew and the supplier.
•Re-run with worst-case dimensions for a safe order.

Common Mistakes

Rounding measurements before calculating.

Enter the full tape reading; rounding early compounds across a job.

Mixing units between fields.

Pick one unit in the dropdown so every conversion is consistent.

Forgetting to verify on site.

Plans differ from as-built work — confirm critical dimensions.

Ordering the bare result with no allowance.

Add the trade waste or contingency factor before buying.

Assumptions

This calculator makes the following assumptions to provide estimates:

Consistent units: All inputs share the selected unit system.

Standard geometry: Flat-plane Euclidean formulas unless stated.

Full precision: Rounding happens only on display, never mid-calculation.

Limitations

Be aware of these limitations when using this calculator:

Estimates, not quotes: Allowances and unit prices vary by region — get 2–3 local quotes.

Verify on site: Confirm critical dimensions before ordering or cutting.

Frequently Asked Questions

Answers to common questions about this calculator.

How much digging is a pool excavation?

Design volume plus ~2 ft overdig each side and 1 ft depth for working room and base — typically 1.5–2× neat. Spoil swells on top.

What soil surprises hit pool excavation digs?

Rock, water and soft spots. Probe or test-pit first; dewatering and rock removal price far above dirt.

Bank vs loose yards — what is the difference?

Bank yards are in-place; loose yards are after digging, swollen 20–35%. Trucks and spoil piles are loose; pay quantities are usually bank.

How accurate is this calculator?

Exact for the dimensions entered. Probe depths and check soil type — subgrade variation and rock move real quantities.

What does the cost estimate include?

Dig, haul or fill at your unit rates on the computed quantities. Rock, dewatering, shoring and testing price separately.

When do I need shoring or sloping?

OSHA requires protection at 5 ft depth and deeper (4 ft in some states). Plan the system before the excavator arrives.

How do I balance cut and fill?

Shrink the cut (divide by ~1.15) to compacted yield, subtract the fill: positive exports, negative imports. Balanced sites haul the least.

What is shrinkage vs swell?

Swell grows dug soil (bank to loose); shrinkage compacts it back smaller than bank (cut to compacted fill). Both move money in opposite directions.

How do I estimate grading production?

Dozers move 50–150+ bank yards/hour by push distance and soil; excavators 30–80. Use fleet history, never brochure peaks.

What slope ratio is stable for fills?

2:1 horizontal-to-vertical or flatter for most unreinforced fills; steeper needs walls, geogrids and drainage design. Water, not angle, usually fails slopes.

How do I set grade stakes?

Hubs with cut/fill marks to finish elevation, guarded and offset from traffic. Stake finish, not cuts — crews build to the lath.

How much does fill shrink when compacted?

About 10–20% (15% typical): 100 loose yards yield roughly 87 placed. Order loose to the placed need.

How many lifts does an embankment need?

Height divided by 8–12 in lift depth, each compacted and tested. Thick dumped lifts never compact through, however long you roll.

What is optimum moisture for compaction?

The water content giving maximum density for that soil — dry of it will not compact, wet of it pumps. Field techs test it; crews feel it with experience.

How do I measure a stockpile?

Cone volume: pi times radius squared times height divided by 3. Measure base diameter and peak height; the repose check validates the shape.

How much clearing debris per acre?

Roughly 20 loose yards for light brush, 40 medium, 80+ heavy timber — plus stumps. Chip, burn where allowed, or haul.

What permits does earthwork need?

Grading, erosion control, tree, wetland and haul-route permits vary by jurisdiction. Fines exceed the dirt cost — check before the first push.

How do I control erosion during earthwork?

Silt fence, stabilized entrances, staged clearing and quick stabilization. Inspect after every rain — regulators do.

Why is my result different from my supplier quote?

Quotes include delivery, minimums, pack-size rounding, tax and regional pricing on top of bare quantities. Compare the net quantities first, then the add-ons.

Do I need a professional for this work?

Measuring and budgeting you can do yourself with this tool. Structural design, permits, licensed trades and inspections still need qualified professionals.

How do I convert the result to other units?

Use the results dashboard conversions, or the dedicated conversion calculators for length, area, volume and weight. Convert each linear dimension before combining into areas or volumes.

What mistakes do beginners make with the pool excavation calculator?

Rounding measurements too early, mixing units between fields, ordering the bare result with no allowance, and skipping site verification. The mistakes section on the page covers each one.

Can I share the pool excavation calculator result with my crew or supplier?

Yes — use the Share result button to send the headline figure and link. The supplier can re-run your numbers from the same inputs.

Does the pool excavation calculator work on a phone at the job site?

Yes — every page is mobile-friendly with no sign-up. Bookmark the tools you use daily for one-tap takeoffs.

How often should I re-run the pool excavation calculator?

Re-run whenever dimensions change, prices move, or you switch materials. Early estimates, pre-order checks and final buy quantities each deserve a fresh run.

What should I check before ordering materials?

Dimensions verified on site, correct unit, waste allowance added, pack sizes and minimums confirmed, delivery access and schedule agreed. The breakdown table is your checklist.

Where do I find the formula behind the pool excavation calculator?

In the formula section below the results, with every variable defined, plus a worked example tracing your own inputs step by step.

How do I read the steps section on the pool excavation calculator page?

Each numbered step shows the inputs used, the formula applied and the intermediate result, ending in the headline figure. Follow it top to bottom to audit the math.

What if my site conditions differ from the page defaults?

Defaults are worked examples, not recommendations — replace every input with your own measurements, prices and allowances before ordering or bidding.

How do I budget for price changes mid-project?

Lock supplier quotes in writing with expiry dates, carry a 5–10% escalation contingency, and re-run the calculator when prices move. Volatile materials get shorter quote windows.

Related Calculators

Explore more calculators related to this topic.

Related Guides

Deepen your understanding with these educational resources.

Cut, fill and hauling basics

Bank vs loose yards, swell, and truck planning.

Pool Excavation Calculator worked examples

Step-by-step pool excavation calculator examples with real job-site numbers.

Excavation, Earthwork & Grading estimating tables

Reference tables, waste factors and coverage rates for excavation, earthwork & grading.

Glossary

Technical terms used in mortgage calculations explained in plain language.

Bank cubic yard: One cubic yard of undisturbed in-place material.
Loose cubic yard: Excavated material after swell — typically 20–35% more than bank.
Swell: Volume growth when soil is dug (20–35% for most soils, up to 50%+ for rock).
Compaction: Mechanical densification of placed fill, usually in 8–12 in lifts.
Cut / fill: Ground removed (cut) or placed (fill) to reach design grade.
Spoil: Excavated material not reused as fill.
cu yd: The primary unit reported by this calculator.

Authoritative References

Trusted sources and standards referenced by this calculator.

OSHA — Trenching & Excavation Safety U.S. Army Corps of Engineers — Earth Manual ASTM — Soil & Rock Standards EPA — Construction Site Runoff

Applicable Standards

OSHA: sloping, benching or shoring for trenches 5 ft and deeperSwell 20–35% for soils (bank → loose); compaction ~15% (loose → compacted)Haul trucks typically 10–16 cu yd loose per loadCall utility locators before any digging

Was This Calculator Helpful?

Report Issue

Page Information

Last Updated:

2026-09-23

Version:

2.0.0

References:

License:

Free to use for educational and professional purposes.