2026-09-24 8 min read
SEER Calculator
Cooling savings from a SEER upgrade — new consumption, saved kWh and saved dollars.
Calculator
Quick presets
Old SEER(SEER) Help
SEER
Existing unit
New SEER(SEER) Help
SEER
Replacement
Annual cooling kWh(kWh) Help
kWh
Yearly use
Rate ($/kWh)($/unit) Help
$
Leave blank for engineering only
Diagram
Sketch for seer calculator with your values. Not to scale — verify on site before ordering.Plan
| Item | Value |
|---|---|
| New useHeadline new use | 3,750.00 kWh/yr |
| SavedSupporting figure | 2,250.00 kWh/yr |
| SavedSupporting figure | 382.50 $/yr |
| Priced value at $0.17/unitMaterials before labor + contingency | $382.50 |
Cost plan
| Materials | $382.50 |
| Labor and install | $0.00 |
| Contingency | $0.00 |
| Project total | $382.50 |
Estimates only — get 2–3 local quotes. Labor varies by region.
Comparisons
| Saved kWh | 2,250.00 |
| Saved ($) | 382.50 |
| Payback @ $5k | 13.07 |
Results
Normal
New use
3,750.00kWh/yr
From kWh2 = kWh1 x SEER1 / SEER2
Saved
2,250.00kWh/yr
Supporting conversion
Saved
382.50$/yr
Supporting conversion
Estimated cost
$382.50
At $0.17/unit
Live results update as you type — currently showing 3,750.00 kWh/yr for seer calculator. Replace the defaults with your own values for an exact takeoff.
Visualizations
Old vs new cooling (kWh/yr)
3,750Your result
6,000Old (6000)
3,750New (~3750)
Project cost split
Materials100%
Labor0%
Contingency0%
Formula
Cooling savings from a SEER upgrade — new consumption, saved kWh and saved dollars.
kWh2 = kWh1 x SEER1 / SEER2
Alternative Form
$ saved = kWh saved x rate
Variables
| Symbol | Name | Unit | Description |
|---|---|---|---|
| V1 | Old SEER | SEER | Existing unit |
| V2 | New SEER | SEER | Replacement |
| V3 | Annual cooling kWh | kWh | Yearly use |
| Q | Result | kWh/yr | Headline answer at full precision. |
Explanation
Inputs convert to consistent units first, the formula runs at full precision, then waste and rounding produce the order figure. Cost multiplies by your unit price.
Step-by-Step Calculation
Follow each step to understand how the result is calculated from your inputs.
Step 1
New use scales with the SEER ratio.
kWh2 = 6000 x 10/16
Result: 3,750 kWh/yr
Step 2
Saved energy and dollars at your rate.
$ = saved x rate
Result: 2,250 kWh = $383/yr
Final Answer
3,750.00
Worked Examples
See how the calculator works with different scenarios.
Scenario
The live inputs above run through the full path below — not just the headline answer.
Inputs
Old SEER:10 SEER
New SEER:16 SEER
Annual cooling kWh:6000 kWh
Calculation
1. New use scales with the SEER ratio. → 3,750 kWh/yr 2. Saved energy and dollars at your rate. → 2,250 kWh = $383/yr
Result
3,750.00 kWh/yr
Interpretation
Order the uplifted figure, never the net: cuts, defects, rounding and code minimums consume the allowance.
Understanding Your Result
Your Result: New use: 3,750.00 kWh/yr
Typical range: SEER 10→16 cuts cooling ~37%; 13→18 saves ~28%.
What This Means
Your result is 3,750.00 kWh/yr (new use). That is the engineered figure — verify it against the code table before buying.
Why It Matters
Sizing drives budget, schedule, deliveries and inspections. Small input errors compound across runs, so modelling before buying is the cheapest due diligence.
Professional Interpretation
Plan around 2,250.00 kWh/yr (saved), about $382.50 at your unit price. Keep same-lot spares for repairs.
How this is calculated
kWh2 = kWh1 x SEER1 / SEER2. Cooling savings from a SEER upgrade — new consumption, saved kWh and saved dollars.
What drives the result
Input size, the selected option, waste % and whole-unit rounding. Unit price never changes quantity — only cost.
Recommendations
- •Split irregular scopes into measurable runs and add the sections.
- •Add waste before ordering: x1.10 straight, x1.15 cut-up, x1.20 complex.
- •Measure twice — lasers beat tapes past 20 ft; photograph nameplates.
- •Keep spares: lots, dye and grain shift between batches.
Educational Content
Introduction
Cooling savings from a SEER upgrade — new consumption, saved kWh and saved dollars.
Concept Explanation
Every calculation reduces to kWh2 = kWh1 x SEER1 / SEER2, evaluated at full precision after unit conversion. The Steps section shows each substitution so the path is auditable.
Applications
▸Planning and takeoffs
▸Bid backup and quote checks
▸Permit documentation
▸Delivery and crew scheduling
▸Verification against supplier quotes
Benefits
- •One live calculation — no separate tools per size or material
- •Steps show every substitution for bid backup
- •Waste and rounding separated from net math
- •Instant cost, charts and lists from the same numbers
Limitations
- •Planning math only — it does not replace stamped design where required
- •Allowances use national planning rates; confirm local stock and prices
- •Irregular geometry should be split into measurable sections
Best Practices
- •Confirm nameplate and table values before ordering
- •Keep one unit per field; watch the steps for conversions
- •Photograph measurements and labels for dispute-proof records
- •Add the trade waste factor before ordering, not after
Common Misconceptions
Myth: Order exactly the computed figure.
Truth: Cuts, defects, fittings and rounding consume 10-20%. Ordering net guarantees a second trip.
Myth: Sticker price picks the cheapest option.
Truth: True cost is installed cost per net unit after waste, labor and contingency — compare that line.
Myth: One rule fits every job.
Truth: Straight runs, retrofits and complex layouts need different allowances — use the sensitivity example.
Practical Tips
- •Run one calculation per run, room or phase, then add the order lines.
- •Pick stock sizes that divide your runs evenly to cut waste several points.
- •Photograph each measurement next to the tape for bid backup.
- •Enter your actual unit price to turn the takeoff into a budget in one step.
Common Mistakes
Ordering the net figure with no waste.
Use the order line: net x (1 + waste%) rounded up to whole units.
Mixing units in one run.
Keep one unit per field; the steps show every conversion explicitly.
Forgetting fittings, slack and extras.
Add equivalents and slack first, then apply waste — in that order.
Ignoring lot/batch differences on the second trip.
Order spares from the same lot up front.
Skipping the verification step.
Recompute one line by hand using the FAQ method before paying.
Assumptions
This calculator makes the following assumptions to provide estimates:
Consistent units: Each field uses its stated unit; conversions run before the formula.
Standard conditions: Water at ~60 F; copper electrical at 75 C terminations unless noted.
Code minimums: Results at or above model-code minimums; local amendments may require more.
Limitations
Be aware of these limitations when using this calculator:
Not a stamped design: Planning and takeoff math; get licensed design where the AHJ requires it.
Estimates, not quotes: Cost plans use allowances and your unit price — get 2-3 local quotes.
Frequently Asked Questions
Answers to common questions about this calculator.
What does the SEER Calculator do?
The SEER Calculator cooling savings from a SEER upgrade — new consumption, saved kWh and saved dollars. Enter your values above and every result, step, chart and plan updates live.
What is the formula behind the SEER Calculator?
The core formula is kWh2 = kWh1 x SEER1 / SEER2. The alternate form shown on the page is $ saved = kWh saved x rate. All math runs at full precision; only the display is rounded.
What inputs does the SEER Calculator need?
Enter Old SEER (SEER, default 10) and New SEER (SEER, default 16), plus Annual cooling kWh (kWh). Live steps show each substitution.
What units does the SEER Calculator report?
The headline result is reported in kWh/yr (new use), with saved in kWh/yr and saved in $/yr beside it. Keep one consistent input unit per field.
How accurate is the SEER Calculator?
Arithmetic follows directly from your inputs using kWh2 = kWh1 x SEER1 / SEER2, so accuracy equals measurement quality. Verify one line by hand (see the verification FAQ), confirm nameplate values, and check against the governing code table before buying.
Can you walk through an example with the SEER Calculator?
With the defaults (old seer 10 SEER, new seer 16 SEER), the calculator substitutes each value into kWh2 = kWh1 x SEER1 / SEER2 in the Steps section and lands on the dashboard headline. Change any input to replay the path with your numbers.
Which code or standard governs the SEER Calculator?
ACCA Manual J/S/D, ASHRAE 62.2/90.1 and IRC Chapter 14 govern the work; the calculator implements the standard math, and your local amendment has the final word.
How does the SEER Calculator price the job?
Enter any unit price and the dashboard, cost plan and pie chart split materials, labor allowances and a 10% contingency instantly. Leave price blank for an engineering-only answer.
What is the most common mistake with the SEER Calculator?
Mixing units (inches vs feet, kW vs BTU/h, yards vs bags) and skipping waste, coverage and rounding allowances. The Steps section exposes every conversion so a slipped unit is visible immediately.
When should I hire a pro instead of trusting the SEER Calculator?
Use the calculator for planning, takeoffs and quote checks; hire a licensed licensed HVAC contractor for permitted work, structural/roof changes, fuel and power connections, and anything the inspector must see. Bring the printed steps — pros quote faster with documented numbers.
How do I stay safe using the SEER Calculator?
A: treat every SEER Calculator project like live work until proven otherwise: 240V disconnects off and verified, gas valves closed before touching burners, and EPA Section 608 certification for anything that opens the refrigerant circuit. The calculator plans the job; licensed pros touch fuel and refrigerant.
What does Manual J mean for the SEER Calculator result?
A: ACCA Manual J room-by-room load calculation is the design standard behind permits and equipment selection. The SEER Calculator gives fast planning/block-load figures from your inputs; run full Manual J software (or hire it) before buying equipment.
How many BTU per square foot should I plan with the SEER Calculator?
A: rule of thumb is 20-25 BTU/h per sq ft of cooling in mixed climates (15 in hot-dry, 30+ in hot-humid or leaky envelopes). Enter your climate-adjusted rate in the SEER Calculator and the steps show the multiplication.
How do tons of AC relate to the SEER Calculator?
A: one ton of cooling equals 12,000 BTU/h. Divide the SEER Calculator headline BTU/h by 12,000 to get tons, then round equipment to the nearest half-ton at or below the load — never above without a Manual J.
How do I convert the SEER Calculator between BTU/h, tons and kW?
A: tons = BTU/h / 12,000 and kW = BTU/h / 3,412. The SEER Calculator dashboard shows all three side by side so bids in any unit cross-check instantly.
What is the difference between EER, SEER and COP near the SEER Calculator?
A: EER is steady-state efficiency, SEER is the seasonal average, and COP is the unitless ratio (EER = COP x 3.412). Higher numbers mean fewer input watts per delivered BTU — the SEER Calculator savings lines use your entered ratings.
How does duct leakage change the SEER Calculator?
A: typical residential ducts leak 20-30% of airflow into attics and crawl spaces. Seal with mastic (not cloth tape) and size equipment to delivered capacity, not nameplate — the SEER Calculator assumes sealed ducts, so discount leaky systems ~25%.
How do I measure rooms for the SEER Calculator takeoff?
A: measure length x width per room, note ceiling height for volume, and record window area by orientation (east/west glass dominates). A laser measurer plus one photo per room beats a tape past 20 ft.
How much extra capacity should I add beyond the SEER Calculator?
A: none — right-size to the load. Oversized equipment short-cycles: clammy rooms, mold risk and compressor wear. If the SEER Calculator lands between sizes, pick the smaller unit unless envelope upgrades are already scheduled.
What thermostat setpoints does the SEER Calculator assume?
A: Manual J design practice: 75 F indoors for cooling, 70 F for heating. Every degree of extra setpoint costs roughly 3% more energy, which the cost plan reflects when you change the defaults.
How does insulation level move the SEER Calculator?
A: upgrading an attic from R-11 to R-38 typically cuts heating/cooling load 10-15%. Re-run the SEER Calculator with the improved envelope rate to quantify the smaller equipment it unlocks.
How does climate zone change the SEER Calculator?
A: heating dominates zones 5-8 and cooling dominates zones 1-3, so the design temperature difference (Delta-T) input carries the zone. Colder zones need bigger Delta-T and higher heating rates per square foot.
What about ventilation and fresh air with the SEER Calculator?
A: ASHRAE 62.2 targets about 7.5 CFM per person plus 3 CFM per 100 sq ft. Tight homes need dedicated fresh air; the SEER Calculator ventilation specs size that fan separately from heating/cooling.
How do I verify the SEER Calculator by hand?
A: recompute one line: BTU/h = area x rate, tons = BTU/h / 12,000, CFM = BTU/h / (1.08 x Delta-T). If hand math differs, check square feet vs cubic feet and Fahrenheit vs Celsius.
What is the biggest mistake the SEER Calculator prevents?
A: sizing from square footage alone with no window, orientation or envelope input — west-facing glass can double a room load. Enter those drivers and the SEER Calculator keeps them visible in the steps.
When should I call an HVAC pro per the SEER Calculator?
A: hire out refrigerant handling, gas piping, 240V circuits, permits, and Manual J/S/D commissioning. Use the SEER Calculator for planning, takeoffs and quote checks; use a licensed contractor for the install.
How does the SEER Calculator treat basements and attics?
A: below-grade and unconditioned spaces get separate treatment — ground contact and roof exposure break the per-square-foot rules. Run the SEER Calculator once per zone instead of lumping the whole house.
How do heat pumps change the SEER Calculator math?
A: the load is identical; what changes is capacity at design temperature. Cold-climate heat pumps hold output near 5 F, but budget backup/strip heat below that — the SEER Calculator cost lines accept your backup inputs.
What maintenance keeps the SEER Calculator result valid?
A: change filters monthly in season, clean coils yearly, verify refrigerant charge, and reseal ducts about every 5 years. A dirty coil alone adds ~30% energy, silently voiding the SEER Calculator payback math.
How do I document the SEER Calculator for a permit or bid?
A: save the steps (inputs, formula, substitutions, result), note design temperatures and envelope assumptions, and photograph nameplates. Contractors quote faster — and inspectors pass faster — with documented numbers.
What is short-cycling and why does the SEER Calculator warn about oversizing?
A: an oversized unit hits the setpoint before wringing out humidity, then restarts minutes later. The result is clammy air, mold risk and short compressor life — right-sizing per the SEER Calculator avoids it.
How does altitude affect the SEER Calculator?
A: air density falls about 3% per 1,000 ft, so combustion appliances derate and the same BTU needs more CFM. Above ~4,000 ft, confirm high-altitude kits and bump fan sizing accordingly.
Related Calculators
Explore more calculators related to this topic.
Related Guides
Deepen your understanding with these educational resources.
Glossary
Technical terms used in mortgage calculations explained in plain language.
- New use
- Headline result of this calculator, reported in kWh/yr.
- Net vs order quantity
- Net is pure math before waste; order adds waste %, coverage and whole-unit rounding.
- Waste factor
- Uplift for cuts, offcuts, defects and rework — typically 10% straight runs, 15% cut-up, 20% complex.
- BTU/h (British Thermal Units per hour)
- Heating/cooling rate; 12,000 BTU/h = 1 ton = 3.517 kW.
- Manual J
- ACCA room-by-room residential load calculation — the design standard.
- CFM (cubic feet per minute)
- Airflow rate; CFM = BTU/h / (1.08 x Delta-T in F).
- SEER2 / EER2 / COP
- Seasonal, steady-state and unitless efficiency ratings; higher is better.
- Delta-T
- Indoor-outdoor design temperature difference driving the load.
Authoritative References
Trusted sources and standards referenced by this calculator.
ACCA — Manual J Residential Load Calculation ASHRAE 62.2 — Ventilation and Indoor Air Quality International Code Council — International Mechanical Code (IMC) Energy Star — Heating and Cooling Guidance U.S. DOE — Energy Saver: Heating & Cooling Home Depot — HVAC Buying Guides
Applicable Standards
ACCA Manual J/S/D govern load, equipment selection and duct design1 ton = 12,000 BTU/h; CFM = BTU/h / (1.08 x Delta-T in F)ASHRAE 62.2 fresh air: 7.5 CFM/person + 3 CFM per 100 sq ftRight-size to the load; oversizing short-cycles and skips dehumidificationMoney rounded for display only; all calculations run at full precision
Was This Calculator Helpful?
Page Information
Last Updated:
2026-09-24
Version:
2.0.0
References:
License:
Free to use for educational and professional purposes.