AtlasCalcsUtility Calculation Suite
2026-09-23 8 min read

Soil Removal Calculator

Free soil removal calculator — plan soil removal: loads, schedule, haul and tipping cost. Includes live results, step-by-step working, charts, material takeoff and cost estimates. No sign-up.

Calculator

Loose volume(cu yd) Help
cu yd

To remove

Truck capacity(cu yd)
cu yd
Cycle time(min) Help
min

Load-haul-dump-return

Haul $/load($) Help
$

Truck rate

Tip $/load($) Help
$

Dump fee

Removal plan

ItemAmount
Haul loadsRounded up8
Last loadPartial2.00 cu yd
Truck-hoursSchedule figure6.0 hr
Removal costHaul + tipping$3,200.00

How to use this result

  • Primary result: 8.00 loads — verify it against a rough hand check before ordering.
  • Read the steps section to see every conversion and the exact formula path.
  • Use the breakdown table on the left as your order or bid checklist.
  • Re-run with worst-case dimensions so the plan covers the whole job.

Results

Optimal

Haul loads

8loads

Rounded up

Last load

2.00cu yd

Partial final load

Truck-hours

6.0hr

Schedule figure

Removal cost

$3,200.00

Haul + tipping

Live results update as you type — currently showing 8.00 loads. Replace the defaults with your own measurements for exact results.

Visualizations

Full vs last load

98Full loads
2Last load

Haul vs tip ($)

Haul63%
Tip38%

Formula

Removal loads with haul and tip cost.

loads = loose ÷ cap, rounded up

Variables

SymbolNameUnitDescription
looseLoosecu ydTo remove.
capTruckcu ydPer load.
loadsLoadscountRounded up.

Explanation

Ceiling division counts loads; cycle time schedules; haul plus tip prices removal.

Step-by-Step Calculation

Follow each step to understand how the result is calculated from your inputs.

Step 1

Loads rounded up.

100 ÷ 14
Result: 8 loads
Step 2

Cycle time totals the schedule.

8 × 45 min
Result: 6.0 truck-hours
Final Answer
8

Worked Examples

See how the calculator works with different scenarios.

Scenario

The calculation run on the values above, showing the full path rather than only the answer.

Inputs

Result:8.00 loads

Calculation

1. Loads rounded up. → 8 loads 2. Cycle time totals the schedule. → 6.0 truck-hours

Result

8.00 loads

Interpretation

Probe every pad and trench, separate topsoil from spoil, and book trucks to the loose volume — not the bank figure.

Understanding Your Result

Your Result: Haul loads: 8 loads

Typical range: Pickup ~2 cu yd · dump truck 10–16 loose cu yd · trench 1 ft × 100 ft × 4 ft ≈ 15 bank cu yd.

What This Means

Your result is 8.00 loads — the bank and loose volumes, truckloads and cost for your soil removal

Why It Matters

Earthwork is the first money spent and the easiest to misjudge: swell multiplies spoil, haul distances multiply cost, and rock stops everything. Quantities first keeps the site moving.

Professional Interpretation

Probe every pad and trench, separate topsoil from spoil, and book trucks to the loose volume — not the bank figure.

How this is calculated

Loads ceil loose volume over truck capacity. Soil factors apply last; trucks round up.

What drives the result

The inputs in a single consistent unit and the allowance or price you apply.

Recommendations

  • •Verify critical dimensions on site before ordering.
  • •Keep one unit throughout each calculation.
  • •Add the trade allowance before buying, not after.
  • •Attach the step-by-step working to bids and records.

Educational Content

Introduction

Earthwork quantity is geometry with soil factors: bank volume from dimensions, loose with swell, compacted with shrinkage, trucks from payload.

Concept Explanation

Loads ceil loose volume over truck capacity. Soil factors apply last; trucks round up.

Applications

▸Pad, trench and basement takeoffs
▸Cut, fill and balance planning
▸Haul truck scheduling and spoil piles
▸Topsoil, base and bedding quantities
▸Grading and compaction estimates

Benefits

  • •Bank, loose and compacted figures together
  • •Swell and compaction factors built in
  • •Truckloads rounded up for scheduling
  • •Free, no sign-up, works on site from a phone

Limitations

  • •Two-dimensional math unless stated otherwise — slopes and curves need the right tool
  • •Results are only as good as the site measurements
  • •Allowances and prices are estimates — confirm with local quotes

Best Practices

  • •Measure twice and write measurements down before typing them in
  • •Keep one unit throughout each calculation
  • •Photograph the tape on large or disputed measurements
  • •Re-run with worst-case numbers so the plan covers the whole job

Common Misconceptions

Myth: The calculator replaces site verification.
Truth: It replaces the arithmetic, not the tape measure — always verify before ordering.
Myth: One decimal place is always enough.
Truth: On long runs, rounding early compounds. Enter full measurements and let the tool round at the end.
Myth: Metric and imperial give different answers.
Truth: They are the same physical quantity in different units — conversion is exact.

Practical Tips

  • •Enter full measurements and let the tool round at the end.
  • •Use the steps section to double-check the formula path.
  • •Save or share the result link with the crew and the supplier.
  • •Re-run with worst-case dimensions for a safe order.

Common Mistakes

Rounding measurements before calculating.
Enter the full tape reading; rounding early compounds across a job.
Mixing units between fields.
Pick one unit in the dropdown so every conversion is consistent.
Forgetting to verify on site.
Plans differ from as-built work — confirm critical dimensions.
Ordering the bare result with no allowance.
Add the trade waste or contingency factor before buying.

Assumptions

This calculator makes the following assumptions to provide estimates:

Consistent units: All inputs share the selected unit system.
Standard geometry: Flat-plane Euclidean formulas unless stated.
Full precision: Rounding happens only on display, never mid-calculation.

Limitations

Be aware of these limitations when using this calculator:

Estimates, not quotes: Allowances and unit prices vary by region — get 2–3 local quotes.
Verify on site: Confirm critical dimensions before ordering or cutting.

Frequently Asked Questions

Answers to common questions about this calculator.

How many loads haul soil off site?
Loose yards ÷ truck capacity rounded up. The last load is partial — still a full trip charge.
What does soil removal cost?
Haul rate per load plus tipping per load or ton. Contaminated soil multiplies tipping — test first.
Bank vs loose yards — what is the difference?
Bank yards are in-place; loose yards are after digging, swollen 20–35%. Trucks and spoil piles are loose; pay quantities are usually bank.
How accurate is this calculator?
Exact for the dimensions entered. Probe depths and check soil type — subgrade variation and rock move real quantities.
What does the cost estimate include?
Dig, haul or fill at your unit rates on the computed quantities. Rock, dewatering, shoring and testing price separately.
When do I need shoring or sloping?
OSHA requires protection at 5 ft depth and deeper (4 ft in some states). Plan the system before the excavator arrives.
How many dump truck loads is my dirt?
Loose yards divided by truck capacity (10–16 typical), rounded up. Book to loose yards — bank math starves trucks and stalls loaders.
What drives hauling cost?
Load count times base rate plus miles times per-mile. Long hauls favor bigger trucks; short hauls favor cycle speed. Distance pricing shows both parts.
How much can an excavator move per hour?
Bucket yards times cycles per hour (100–150 typical) times efficiency near 83%. A 1-yard bucket runs about 100 loose yards/hour with trucks balanced.
What limits excavator production?
Truck availability first, then swing angle, dig depth, soil and operator skill. Balance the truck fleet to the hoe, not the other way.
How do I schedule haul trucks?
Divide loads by loads-per-day-per-truck for days, and stage arrivals to the loader cycle so neither waits. Queues and gaps both burn money.
What is a cycle time made of?
Load, haul, dump, return and spot — measure a few rounds and use the average. Traffic and dump queues dominate long hauls.
How much does tipping/dumping cost?
Varies wildly: tens per load for clean fill, far more for mixed, contaminated or restricted waste. Test suspicious soil before pricing disposal.
Can I reduce haul cost?
Balance cut and fill on site, stockpile reusable topsoil separately, shorten hauls with closer disposal, and upsize trucks on long runs.
What paperwork do haul-offs need?
Tickets for every load, manifests for regulated material, permits for overweight or night hauls. Reconcile tickets to the plan weekly.
How do I handle the last partial load?
It still costs a full trip. Rebalance trucks, combine with another pickup, or confirm the short-load terms before dispatch.
What is backhauling?
Trucks returning loaded instead of empty — import fill on the backhaul of an export run. Coordinated hauls cut both costs nearly in half.
How do weight limits affect loads?
Wet soil hits legal weight before volumetric capacity. Know payload in tons as well as yards, and scale-check heavy or wet hauls.
How do I measure correctly for the soil removal calculator?
Measure twice with a tape or laser, write every reading down before typing it in, and keep one unit throughout. Photos of the tape protect you on disputed dimensions.
What units does the soil removal calculator use?
Whatever unit you select — pick one and use it for every field so conversions stay consistent. Results convert to the common trade units automatically.
How accurate is the soil removal calculator?
Exact for the numbers entered: all math runs at full precision and rounds only for display. Field accuracy depends on your measurements, so verify critical dimensions on site.
Can I use the soil removal calculator for bids and quotes?
Yes — the steps section shows the full working, and the breakdown table lists order quantities. Attach both to bids so clients see net figures and allowances separately.
Should I add waste or contingency to the result?
Yes. Add the trade waste factor (5–20% depending on material) before ordering, and carry a separate 5–10% budget contingency for price movement and surprises.
Why is my result different from my supplier quote?
Quotes include delivery, minimums, pack-size rounding, tax and regional pricing on top of bare quantities. Compare the net quantities first, then the add-ons.
Do I need a professional for this work?
Measuring and budgeting you can do yourself with this tool. Structural design, permits, licensed trades and inspections still need qualified professionals.
How do I convert the result to other units?
Use the results dashboard conversions, or the dedicated conversion calculators for length, area, volume and weight. Convert each linear dimension before combining into areas or volumes.
What mistakes do beginners make with the soil removal calculator?
Rounding measurements too early, mixing units between fields, ordering the bare result with no allowance, and skipping site verification. The mistakes section on the page covers each one.
Can I share the soil removal calculator result with my crew or supplier?
Yes — use the Share result button to send the headline figure and link. The supplier can re-run your numbers from the same inputs.
Does the soil removal calculator work on a phone at the job site?
Yes — every page is mobile-friendly with no sign-up. Bookmark the tools you use daily for one-tap takeoffs.
How often should I re-run the soil removal calculator?
Re-run whenever dimensions change, prices move, or you switch materials. Early estimates, pre-order checks and final buy quantities each deserve a fresh run.

Related Calculators

Explore more calculators related to this topic.

Related Guides

Deepen your understanding with these educational resources.

Glossary

Technical terms used in mortgage calculations explained in plain language.

Bank cubic yard
One cubic yard of undisturbed in-place material.
Loose cubic yard
Excavated material after swell — typically 20–35% more than bank.
Swell
Volume growth when soil is dug (20–35% for most soils, up to 50%+ for rock).
Compaction
Mechanical densification of placed fill, usually in 8–12 in lifts.
Cut / fill
Ground removed (cut) or placed (fill) to reach design grade.
Spoil
Excavated material not reused as fill.
cu yd
The primary unit reported by this calculator.

Authoritative References

Trusted sources and standards referenced by this calculator.

Applicable Standards

OSHA: sloping, benching or shoring for trenches 5 ft and deeperSwell 20–35% for soils (bank → loose); compaction ~15% (loose → compacted)Haul trucks typically 10–16 cu yd loose per loadCall utility locators before any digging

Was This Calculator Helpful?

Page Information

Last Updated:

2026-09-23

Version:

2.0.0

License:

Free to use for educational and professional purposes.